The BASE is a single-stage impulse turbine. The favourably priced turbine was designed as a generator drive for the 75-1000 kW power range and can be used in small combined heat and power (CHP) plants, in decentralised solar facilities as well as for waste-heat recovery, e.g. used in bottoming cycles attached to gas engines and biogas engines or for the utilisation of residual process steam.
The BASE for mechanical drives is a single-stage, backpressure steam turbine in which the flow passes axially through the blading. It is mainly used as a power source for pumps or fans and especially as a stand-by unit with quick-start capability.
The CORE is perfectly suitable for packaging companies / EPCs who complete the unit for their customers. We deliver the core unit with gear only.
Technical data
Power output up to 1,000 kW
Inlet pressure up to 40 bar(a)/580 psi
Inlet temperature dry saturated steam up to 400°C/750°F
Generator 50 Hz/60Hz
Backpressure up to 11 bar(a)/160 psi or vacuum
Technical data
Power output up to 750 kW
Inlet pressure up to 101 bar(a)/1,465 psi
Inlet temperature dry saturated steam up to 500°C/930°F
Speed acc. to driven machine
Exhaust pressure: back pressure up to 11 bar(a)/160 psi
Technical data
Power output up to 6 MW
Inlet pressure up to 131 bar(a)/1,900 psi
Inlet temperature dry saturated steam up to 530°C/985°F
Speed acc. to driven machine
Exhaust pressure: back pressure up to 29 bar(a)/420 psi or vacuum
Backpressure or condensing type
Package unit design, oil unit integrated in base frame
Extremely small and compact design
Only minimal foundation work required
Largely maintenance-free, robust construction
High availability thanks to resilient and sure technology
Quick start without preheating of the turbine
Favourably priced thanks to proven components
Quick installation and commissioning
Features
Low-maintenance because of the simple design
Extremely failure safe
Quick-start compatible
Turbine with integral oil supply
Meet requirements of API 611/612**
ATEX version available
*Turbine only. **If overhung design and integral gear is accepted.
Features
Backpressure or condensing type
Nozzle group control valves available
Quick-start without pre-heating
Meet requirements of API 611/612*
*If overhung design and integral gear is accepted
MONO
Up to 6 MW
TWIN
Up to 7 MW
TRI
Up to 12 MW
The MONO stand out by their rugged design and renowned reliability even under the most severe operating conditions. They are ideal for saturated steam service. Their suitability for use as condensation or back-pressure turbines in combination with various integral gears modules opens up a broad application range.
The TWIN provides highest cost efficiency and high performance. It allows to reduce high heat gradients while providing a controlled extraction capability. The TWIN is a dual casing turbine on one gearbox which can run on different steam lines.
The TRI is a triple casing steam turbine with an integrated gearbox, designed for flexible operation and high efficiency. The multi-casing design allows for up to two controlled extractions as well as for operation on different steam supply systems.
Technical data
Power output up to 6 MW
Inlet pressure up to 131 bar(a)/1,900 psi
Inlet temperature dry saturated steam up to 530°C/985°F
Speed acc. to driven machine
Exhaust pressure: back pressure up to 29 bar(a)/420 psi or vacuum
Technical data
Power output up to 7 MW
Inlet pressure up to 131 bar(a)/1,900 psi
Inlet temperature dry saturated steam up to 530°C/985°F
Speed acc. to driven machine
Exhaust pressure: back pressure or vacuum
Technical data
Power output up to 12 MW
Inlet pressure up to 131 bar(a)/1,900 psi
Inlet temperature up to 530°C/985°F
Exhaust pressure: up to 0.06 bar (a)/8.7 psi condensation
Length approx. 6 m/20 ft (incl. generator)
Width 2.8 m/9.2 ft
Height 3.2 m/10.5 ft
Typical dimensions
Length approx. 8 m/26.2 ft (incl. generator)
Width 4 m/13.1 ft
Height 4 m/13.1 ft
Features
Backpressure or condensing type
Package unit design
Oil unit integrated in base frame
Nozzle group control valves available
Quick-start without pre-heating
Tailor made
*Turbine only.
Features
Backpressure, condensing type
Package unit design
Oil unit integrated in base frame
Nozzle group control valves available
Quick-start without pre-heating
Extremely compact construction
Pressure controlled extraction
High pressure/low pressure applications
Features
Condensing type
Package unit design
Oil unit integrated in base frame
Nozzle group control valves available
Quick-start without pre-heating
Extremely compact construction
Pressure controlled extraction
High pressure/low pressure applications
Reheat possible
English
Türkçe
